Products
Categories
Plastic Labware
TEST TUBE ROTATOR:
| Ideal for mixing for diffusion, dialyzing, extraction etc. Comprises a sturdy circular disc with flexible, plastic coated spring clips for holding test tubes of diameter 10-30mm and is mounted on the rotor assembly. The rotor assembly has variable speed motor with provision for adjusting rotational speed from 5 to 50 RPM. Also incorporates a user set table timer from 0-99 hours / 1-59 minutes. The complete rotor assembly is supported on two parallel vertical pillars by thumb screws providing secured clamping and provides for adjustment of angle of rotation of the test-tubes disc anywhere between horizontal (for minimal mixing) to vertical (for full end over end mixing). The electronic touch-panel control allows for convenient operation, which is further substantiated by large sized digital LED display. Operates on 220V AC, 50Hz. |
|
| Cat. No. | Description |
| 2051240/1 | Rotospin Test Tube Rotator |
| 2051240/2 | Disk for 24 x 1.5 mL tubes |
| 2051240/3 | Disk for 18 x 15 mL tubes |
| 2051240/4 | Disk for 12 x 50 mL tubes |
TEST TUBE STAND
| Most commonly used test tube stand. Rack with six holes is supported at each end by a vertical column. The top plate has 2 holes for 25mm tubes and 4 holes for 16mm tubes with corresponding recesses at the bottom plate just below the holes. Bottom plate also has 6 vertical pegs for drying test tubes. |
|
| Material: Polypropylene | |
| Cat. No. | Particulars |
| 2072560 |
16 mm & 25mm ø tubes 25 mm ø tubes |
.jpg)
TEST TUBE STAND (3TIER)
| Made of polypropylene, these racks feature 3-tier design that provides clear view of tube contents, and allows convenient insertion and removal of tubes. Chemical and corrosion resistant, autoclavable, and can withstand sub-freezing temperatures. Available for (tubes diameter × No. of tubes) |
|||
| Material: Polycarbonate | |||
| Cat. No. | Particulars | Cat. No. | Particulars |
| 2072840/1 | 13 mm x 31 tubes | 2072840/2 | 16 mm x 31 tubes |
| 2072840/3 | 20 mm x 20 tubes | 2072840/4 | 25 mm x 12 tubes |
| 2072840/5 | 25 mm x 18 tubes | 2072840/6 | 32 mm x 12 tubes |
| 2072840/7 | 25 mm x 36 tubes | 2072840/8 | 13 mm x 18 tubes |
| 2072840/9 | 15mm x 18 tubes | 2072840/10 | 18 mm x 12 tubes |
| 2072840/11 | 13 mm x 62 tubes | 2072840/12 | 16 mm x 62 tubes |
| 2072840/13 | 20 mm x 40 tubes | 2072840/14 | 13 mm x 48 tubes |
| 2072840/15 | 13 mm x 72 tubes | ||
TEST TUBE STAND (3TIER)
| Made of polycarbonate. Excellent for use in tissue culture labs, Pharmaceuticals testing. Three tire design. End plates have handgrips for easy handling. With transparent upper and middle plates. Autoclavable, can withstand sub-freezing temperature. |
|||
| Material: Polycarbonate | |||
| Cat. No. | Particulars | Cat. No. | Particulars |
| 2072880/1 | 13 mm x 31 tubes | 2072880/2 | 16 mm x 31 tubes |
| 2072880/3 | 20 mm x 20 tubes | 2072880/4 | 25 mm x 12 tubes |
| 2072880/5 | 13 mm x 62 tubes | 2072880/6 | 16 mm x 62 tubes |
| 2072880/7 | 20 mm x 40 tubes | 2072880/8 | 25 mm x 24 tubes |
| 2072880/9 | 25 mm x 18 tubes | 2072880/10 | 25 mm x 36 tubes |
| 2072880/11 | 32 mm x 12 tubes | ||
TEST TUBE STAND (ROUND)
| Handy, space saving, round shape, made of polypropylene, for 12 tubes 4 of 25mm diameter and 8 of 19mm diameter through the holes on the top plate, which is supported on bottom plate through 4 vertical pins. The base has recesses corresponding to the holes in the top plate, 16 vertical pegs for drying test tubes and is surrounded by a trough shape to contain drippings. This autoclavable stand can be easily disassembled for cleaning. |
|
| Cat. No. | Particulars |
| 2072600 | 19 mm. & 25 mm ø tubes |
TEST TUBE STAND, MICRO TUBES
| Moulded in polycarbonate, these autoclavable racks hold 1.5ml micro centrifuge tubes. Racks are stackable which prevents movement in any direction. The holes are numbered and lettered for easy identification. |
|
| Material: Polycarbonate | |
| Cat. No. | Particulars |
| 2072640/1 |
24 tubes |
| 2072640/2 | 48 tubes |
TEST TUBE STAND, PLASTIC
| A single piece, moulded plastic test tube stand has 2 rows of 6 holes each to take up to 12 test tubes 4 holes of about 25mm diameter and 8 holes of 16mm diameter. also has five vertical pegs for draining. The single piece moulding makes it long-lasting and durable. | |
| Cat. No. | 2072580 |
TEST TUBE WITH SCREW CAP
| Polypropylene test tubes, provide excellent option for RIA, coagulation and bacteriology etc. Features excellent contact clarity and are autoclavable. Provided with cap screwed on to the tube, making is usable by filling it up to the brim. Size (height × diameter) 100 × 16mm. |
|
| Material: Polypropylene | |
| Cat. No. | Particulars |
| 2067500 | 16 x 100 mm Ext. Thread |
THERMOSTATIC WATER BATH, WITH EVAPORATION LID
| A low cost water bath, which is fully compatible substitute for expensive ones. The completely transparent tank has seamless construction and is made of polycarbonate plastic that can withstand 120ºC. Fast acting thermostat also serves as low-water-level protector, providing safety against heating element burn-out and fire hazards, and incorporates temperature setting in ºC from ambient to 100ºC. The thermostat allows for temperature control accuracy of about ±0.3ºC ensures precise test conditions. When combined with evaporation lid, this water baths becomes a boiling bath. The evaporation lid has six opening of about 105mm diameter, which are equipped with concentric rings to reduce the diameter of the openings to accommodate container of different sizes. | |
| Cat. No. | 2052040 |
TOUGH TAGS / TOUGH SPOTS
| These are chemically inert polyester labels which will strongly adhere to all plasticsand other material. They are temperature resistant from -40°C to 121°C. Theselabel will withstand autoclaving, boiling water baths, freezer temperatures, organic solvents, caustic agents and other challenges without peeling. | ||
| Cat. No. | Description | (l×b) mm |
| 5060250/1 | Tough Tags | 24×12.7 |
| 5060250/2 | Tough Tags | 32.5×12.7 . |
| 5060250/3 | Tough Spots | dia.-9.5 |
| Tough Tags. For colour put the following suffix after the code No. | ||
| B = Blue, G=Green, R = Red, W=White. | ||
| Tough Spots. For colour put the following suffix after the Code No, B=Blue, | ||
| C=Coffee,D=Gold, G=Green, L=Lavender, M=Maroon, O=Orange, | ||
| P=Pink, R=Red, Y=Yellow, W=White | ||
TOUGH TAGS STATION
| Tough Tag Station holds upto six standard sized boxes of Tough-Tags. Tough Spots Or Cryo Babies. | |
| Cat.No. | 5060300 |
TRAPAZODIAL MAGNETIC STIRRING BAR
| The high energetic Rare earth magnet has higher torque and efficiency as compared to conventional stirring bar |
|
| Material : PTFE / Alnico V Magnet | |
| Cat. No. | (f x I) mm |
| 5040900 |
20 x 45 mm |
TRIANGULAR MAGNETIC STIRRING BAR
| Comprising strong magnets coated with PTFE to provided long-life stirring operation. For use along with magnetic stirrers. |
|
| Material :PTFE / Alnico V Magnet | |
| Cat. No. | (HxL) mm |
| 5040750/1 | 14 x 30 mm |
| 5040750/2 |
14 x 40 mm |
| 5040750/3 | 14 x 50 mm |
Triangular Shape Bottles With Handle R.M. HDPE
| This new triangular shape bottles are thick walled have strong side handles for easy carrying and have cap with induction sealing wad. | |
| Capacity in ltr. | Case of |
| 2.5 | 1 pcs |
UNIVERSAL MULTI RACK
| The rack is designed to be compatible with wide range of tube diameters. This rectangular shaped rack has holes on all the four sides to take tubes of diameters 30mm, 20mm, 17mm and 12mm, respectively. |
|
| Material: Polycarbonate | |
| Cat. No. | Particulars |
| 2072720/1 |
Multi Rack |
UNIVERSAL REAGENT RESERVOIR
| This universal reagent reservoir is a graduated single reagent reservoir with a maximum volume of 50mL on one side and a reservoir with eight separate numbered reagent channels of capacity 5mL each along with a reservoir with twelve separately numbered reagent channels also of 5mL capacity on the other side. Made of polypropylene, these reagent reservoirs are repeatedly autoclavable and can be used with all multichannel pipettes. | |
| Material: Polypropylene | |
| Cat. No. | Particulars |
| 2061060 | 50 mL |
URINE CONTAINER
| These containers can be used for collecting a wide range of samples of sputum, urine etc. Moulded in polypropylene these container have excellent contact clarity and the cap has built-in seal that makes it completely leakproof. | |
| Material: Polypropylene | |
| Cat. No. | Particulars |
| 5051850/1 | 30 mL |
| 5051850/2 | 60 mL |
UTILITY TRAY
| Adding to the already existing range of autoclavable laboratories trays, is the Utility Tray and as the name suggests this Polypropylene Tray can be utilized for purposes ranging from drying glassware to sterilizing and to store any laboratory apparatus. |
|
| Material: Polypropylene | |
| Cat. No. | Particulars |
| 5014300 | 375 x 350 x 130 mm |
VORTEX SHAKER
| Compact, rugged and durable construction designed for continuous use. Heavy, stable metal base with non-skid rubber feet prevents unnecessary movement of the shaker during use. A heavy duty, variable speed motor delivers quiet and reliable operation with continuous speed variation through a knob at the front, with a maximum speed of about 300 RPM. Also allows for the choice of continuous mode or touch mode, selectable through a rocker switch on the front panel. Operates on 220-240V AC, 50/60Hz. | ||
| Cat. No. | 2050920 | |
| 2051160 | Spinix | |
| 2051160/1 | Spare cup attachment | |
| 2051160/2 | Spare one hand attachment | |
| 2051160/3 | Spare one hand insert | |
| 2051160/4 | Spare micro tube insert | |
WATER BOTTLE FOR ANIMAL CAGE
| Autoclaveable Polypropylene bottles having caps with moulded-in stainless steel sipper tubes. Available in capacities |
|
| Material: Polypropylene / Stainless Steel | |
| Cat. No. | Particulars |
| 4120500/1 | Straight nozzle, 125 mL |
| 4120500/2 |
Straight nozzle, 250 mL |
| 4120500/3 |
Bent nozzle, 125 mL |
| 4120500/4 | Bent nozzle, 250 mL |
